Enjoying a spa is a really rewarding experience that relaxes us and helps improve our well-being. Among the many advantages of these portable spas is the fact that they can be used at any time of the year. Adjust the temperature of the water you can cool off in summer or take a warm and restful bath when the cold increases. We suggest visiting laser hair removal in Manhattan.
Table of ContentsToggle
If you are the lucky owner of an inflatable spa, you should know that performing simple maintenance tasks is essential to be able to enjoy it correctly. Extend your life as much as possible. But how to keep an inflatable spa in optimal conditions? Then we give you the keys.
For starters, it is very important to maintain an adequate chemical balance of the water, so that it is safe. Factors such as weather variations or organic waste such as sweat, soap, etc. lead to alterations in the water that generate algae and bacteria. It must be eliminated through the use of disinfectant chemicals. This maintenance task is the most important since keeping the water clean prevents us from contracting infections or diseases. Visit the wax centers in midtown Manhattan to get the best care for waxing.
The chemical parameters of the water to be checked and adjusted periodically are the following, in the order indicated:
It indicates the degree of resistance to pH change. The alkalinity should be between 80 and 120 ppm (parts per million). Because the pH value will be greatly affected by the alkalinity value. This will be the first that we should measure and control. If the alkalinity is too low, it will cause corrosion in metal parts, skin and eye irritation, and difficulty adjusting the pH. If it is high, it will induce accumulation of lime, cloudy water, irritation of eyes and skin, and high demand for chlorine.
This indicates whether the water is acidic or basic. It should be maintained between 7.2 and 7.6, ideally between 7.2 and 7.4. A high value indicates that the water is too basic. It can cause low efficiency of chlorine, cloudy water, eye and skin irritation, and lime accumulation.A low level means that the water is acidic, which would cause corrosion of the metals and irritations.
Both chlorine and bromine are very effective disinfectants, the former is widely used in swimming pools, while the latter is used more specifically in hot water pools and in spas.
Chlorine meters usually measure 3 different values: total chlorine, free chlorine (which is the useful color concentration), and residual chlorine. It is the one that no longer has a disinfectant effect. Of the above, the most useful is free chlorine, which must be between 1 and 2 ppm.
Regarding bromine, we must measure the total amount present in the water, which should be between 4 and 5 ppm.
If the result is too low, the level of disinfection will be inappropriate. If the result is too high, there may be problems with odor, skin and eye irritation, corrosion of metals and other materials.
The disinfectant margin must be somewhat greater than in swimming pools. It makes the body provides a greater proportion of organic waste such as sweat, skin, urea, and bacteria, being more prone to the proliferation of germs.
These chemical components should be checked frequently, using a chlorine/bromine and pH analyzer kit. If necessary, bring the strips from the spa manufacturer. The ideal in the bathing season is to do it daily to be able to adjust the values after each use. If we are not using it, then we can reduce the periodicity up to once a week.
If the values are not adequate, we will make the necessary adjustments using incremental or minor chemical products, following the manufacturer’s dosage instructions. Each time we adjust a level, we must circulate the water, measure again after one hour, readjust if necessary and check the next value.
It is also good to check the hardness of the water. This is the amount of calcium and magnesium salts dissolved in it. In areas where the water is hard, water accumulation in the circuits, turbidity in the water, and irritation can be caused. These effects can be prevented by using an antical. It will not be necessary for those spas, such as those of the Intex brand, which already incorporate an anti-water treatment system.
To prevent the growth of algae, we must maintain the appropriate levels of chlorine and PH. If it is not enough, we will resort to an algaecide. When applying the chemical treatment of water, you must take into account the following tips:
Apart from chemical adjustments, the maintenance of our spa requires other simple cleaning tasks, to eliminate solid waste that falls from the environment and that we deposit ourselves.
Turn on the filtration of the equipment usually for a few hours, in the bathing season, do it daily. Wash and replace the filter cartridge periodically. How often? That depends on how often you use the spa and the quality of the water you use. You can rinse it from time to time with clean water to remove dirt that may affect its operation, approximately every week or every 2 weeks. If you notice that the filter gets dirty again right away and becomes a bit discolored. It will not be fulfilling its function well and you should change it to a new one.
Sometimes the dust particles are so thin that the sewage plant does not retain them. A flocculant is needed for the removal of these particles. It is a product that increases its size and causes its decantation to the bottom. So, it can be easily cleaned with a vacuum cleaner. When adding flocculant, you should not bathe until you vacuum, since although it is not toxic. It is better not to be in contact with it.
Keep in mind that if there is dirt in the water or it becomes cloudy and the chemicals cannot clean it. You should change the water and clean the spa bathtub. To do this, use a sponge and mild soap to clean dirt or stains from the walls. Then rinse thoroughly before refilling it with water.
If you are very dirty or sweaty, it is advisable to take a shower before entering the spa. So, you avoid facilitating the proliferation of germs. Always disconnect the spa for maintenance or repair.
If a correct filtration and chemical control of the water is maintained with adequate levels, the water can last up to 2 or 3 months. After this period, it is convenient to renew the water. As an additional hygienic measure, if the renewal is clean every 30 or 40 days so much the better. You will avoid the formation of algae or compounds that at first sight can go unnoticed.
When the spa is not being used, the cover with safety locks should be placed. This avoids potentially dangerous situations, especially when there are children nearby. If the spa is located outside, the deck will prevent leaves, insects, and other solids from falling and prevent it from filling in case of rain.
When the spa is located outside, you should take extra precautions. It is to protect it from both excessive cold and continued exposure to UV rays. If the temperature drops below 0 degrees Celsius, do not leave it in the open as frost could damage it. All PVC-derived materials degrade with excessive exposure to sunlight. It may be deformed if we do not protect it with a cover or awning. Finally, we recommended Waxing studio Manhattan and the Best facial for acne in Manhattan to know more details.